Ease Release 2831 for use with FlexFoam

SKU
SO2831
$16.78

Ease Release 2831 for use with FlexFoam

Ease Release 2831

is a wax-based non-silicone liquid release agent. It has proven to be effective when used to release polyurethane foams. This wax dispersion is designed to operate at mold temperatures ranging from 160°F to 200°F with minimal wax build-up. EASE RELEASE 2831 works with aluminum, steel, and elastomeric mold construction.

Features

Product Specifications
AppearanceHazy Liquid
Solids6 – 7%
Temperature160°-200°F
(71°-93°C)
ApplicationSpray
ViscosityMedium
  • Excellent release
  • Non-silicone
  • Contains no chlorinated or CFC solvents
  • Low wax build-up

Ease Release 2831 provides

  • Excellent release
  • Excellent surface finish
  • No build-up on mold surfaces
  • Reduced mold maintenance and down time
  • Greater productivity

CAUTION

At temperatures above 500°F, fumes are evolved which, if inhaled, can cause flu like systems. Use with adequate ventilation.

Application

  1. Clean molds with Mold Cleaner 2508, for a clean mold surface prior to preparing the molding surface.
  2. Heat the mold to operating temperature.
  3. Apply a coat of EASE RELEASE 2831 with a spray or brush and allow too dry.
  4. Rub EASE RELEASE 2831 into mold surface with a clean cloth.
  5. Repeat two or three times to seal the mold surface.
  6. Start molding and reapply a light coat of EASE RELEASE 2831 after each molding cycle.

Finishing

Thorough cleaning of molded parts with Isopropyl Alcohol may be required prior to staining, painting, or bonding. For suggested cleaning procedures, consult your Mann technical representative.

Ease ReleaseWeight
/Gallon
Solvent CarrierDrying RateFlammableWetting Quality
Ease Release 28316.0#Petroleum HydrocarbonsMediumYesExcellent
Quantity23 OR

Ease Release 2831

is a wax-based non-silicone liquid release agent. It has proven to be effective when used to release polyurethane foams. This wax dispersion is designed to operate at mold temperatures ranging from 160°F to 200°F with minimal wax build-up. EASE RELEASE 2831 works with aluminum, steel, and elastomeric mold construction.

Features

Product Specifications
Appearance Hazy Liquid
Solids 6 – 7%
Temperature 160°-200°F
(71°-93°C)
Application Spray
Viscosity Medium
  • Excellent release
  • Non-silicone
  • Contains no chlorinated or CFC solvents
  • Low wax build-up

Ease Release 2831 provides

  • Excellent release
  • Excellent surface finish
  • No build-up on mold surfaces
  • Reduced mold maintenance and down time
  • Greater productivity

CAUTION

At temperatures above 500°F, fumes are evolved which, if inhaled, can cause flu like systems. Use with adequate ventilation.

Application

  1. Clean molds with Mold Cleaner 2508, for a clean mold surface prior to preparing the molding surface.
  2. Heat the mold to operating temperature.
  3. Apply a coat of EASE RELEASE 2831 with a spray or brush and allow too dry.
  4. Rub EASE RELEASE 2831 into mold surface with a clean cloth.
  5. Repeat two or three times to seal the mold surface.
  6. Start molding and reapply a light coat of EASE RELEASE 2831 after each molding cycle.

Finishing

Thorough cleaning of molded parts with Isopropyl Alcohol may be required prior to staining, painting, or bonding. For suggested cleaning procedures, consult your Mann technical representative.

Ease Release Weight
/Gallon
Solvent Carrier Drying Rate Flammable Wetting Quality
Ease Release 2831 6.0# Petroleum Hydrocarbons Medium Yes Excellent

Warning WARNING: This product can expose you to chemicals including Silica, crystalline (airborne particles of respirable size), which are known to the State of California to cause cancer.  For more information go to www.P65Warnings.ca.gov.