BronzClay Kit, Charcoal, Vessel & Clay


BronzClay Kit - Everything you need to get started (except the kiln) You can use any kiln that can be programed or you need a pyrometer. This is the smallest kit, only what you need to get going!, contains the small vessel, enough charcoal for 50+ firings and 100 grams of bronzclay. 

In Stock Now8 OR

Your Guide to Welcome to BRONZclay™!

 BRONZclay™ is easily sculpted, molded, carved and formed, and becomes solid bronze when fired. Your imagination and just a few simple tools will allow you to create solid bronze pieces—jewelry to sculptures and everything in between! Working with BRONZclay™ BRONZclay™ is just that: a clay. Like clay, it’s highly workable but it also dries quickly. You’ll notice the clay stiffening and cracking when it begins to dry. 

Some tips to keep in mind: 

• Keep BRONZclay™ refrigerated until you’re ready to use it and in between sessions. 

• Rub a dab of olive oil on your hands before you begin working with the clay. 

• While working the clay, refresh it periodically with a small amount of water using a spray bottle or brush. 

• Wrap pieces that you are not currently working on in plastic and place to the side. 

• Avoid using tools that absorb water. 

• When not in use, keep the clay tightly wrapped in plastic and place the wrapped piece in a sealed plastic bag for added protection. 

Store all unopened packages (as well as opened packages) of BRONZclay™ in a refrigerator when not in use. Making Slip Slip will quickly become one of your favorite tools for working with BRONZclay™, and it’s easy to make. Simply mix tiny pieces of clay (filings, small dried or wet pieces, etc.) with water (we recommend distilled water for a longer shelf-life) until you reach a yogurt consistency. Keep your slip stored in a sealed container. Note: Slip will last for about one week, so make only enough for your immediate need. 

Drying the Clay Once you’ve finished your piece, you will need to dry the clay before firing it. Gently place the piece on a warming surface such as a coffee mug warmer; an inexpensive vegetable dehydrator works well, too. Once dry, you’ll notice the clay is leather hard, making it very easy to add finishing touches such as filing, drilling, sanding and carving. Once BRONZclay is fired, it’s much more difficult to finish, so take advantage of this pre-fired stage to do as much of your detailed finishing work as possible. 

Firing To reduce oxidation, the piece(s) must be surrounded by activated carbon during firing. Firing BRONZclay™ is a two-step process that uses low heat to vaporize the binder, then high heat to sinter the alloy. 

1) Spread 1" of activated carbon granules on the bottom of a stainless steel firing container  

2) Place the piece on top of the layer; if firing two or more pieces, leave at least 1/2" between pieces, more if the pieces are large. 

3) Pour more activated carbon granules on top of the pieces until the container is filled 1" from the top, making sure there is a 1/2" layer of granules on top of the pieces. Again, if you are firing many pieces in layers, make sure there is at least 1/2" of space between the vertical layers as well. Note: Do not fire more than 100 grams of clay at once; overloading may cause poor sintering. 

4) Put the stainless steel lid on the firing container and place it in the kiln on stilts to allow good heat circulation. 

Note: Most kilns are cooler in the front near the door, so the front of your firing container will be cooler than the other sides. Compensate for this by placing the pieces closer to the sides and back of the firing container. If you have a top-loading kiln, there’s no need to adjust. 

Firing Thin Pieces: For pieces that are 6 cards (3mm) thick or less, fire according to the following program: Ramp at 500°F/hour to 1550°F, and hold for 2 hours. Total firing time (including warm-up) will be between 4 and 5 hours. 

Firing Thick Pieces: For pieces that are thicker than 6 cards (3mm), fire according to the following program (this firing schedule will also work for thin pieces): Ramp at 250°F/hour to 1550°F, and hold for 3 hours. Total firing time (including warm-up) will be about 9 hours. 

Finishing Once fired, the BRONZclay™ piece is a solid piece of metal. As with other metals, it can be sawn, drilled, sanded, patinated or soldered using traditional jewelry tools and materials. 

 Safety The binder in BRONZclay™ is non-toxic, and no toxic fumes will be present during firing. Though rare, it is possible for some individuals to experience some sensitivity to BRONZclay™. We recommend wearing a dust mask while working with the activated carbon. 

Warning WARNING: This product can expose you to chemicals including Silica, crystalline (airborne particles of respirable size), which are known to the State of California to cause cancer.  For more information go to